DIY Stool



For original article click here

Step 1: Creating the Legs

Creating the LegsCreating the Legs

First, start off with your 2×4 piece of wood. You will need 4 of these cut to a length of 30 inches. These will serve as your legs.
To make the legs slanted, cut at a 7-degree angle perpendicular to the short length of the base of the wood. This will need to be done to both sides so the bases of the piece will be parallel.

Step 2: Creating the Cross

Creating the CrossCreating the Cross

In order to connect the legs, there will be a cross that will hold the 4 legs together.

Start with 2 1×1 pieces of wood that are 13 inches long. Mark up a 1/2 inch by 3/2 inch box from the edge of the long side of the 1×1.

To cut out the square, start by making multiple small cuts from the ledge to the inside of the box drawn.

After a few cuts start chiseling out the pieces of wood and sand the inside until the two pieces of wood can fit together.

In order for the cross to be able to fit with the legs, make a 7-degree cut at the sides of the 1×1. The 7-degree cuts should be pointing towards each other and not parallel to make a frustum shape.

Apply wood glue to connect the pieces and use clamps to apply pressure and make sure they dry correctly

Step 3: Connecting the Legs and Cross

Connecting the Legs and CrossConnecting the Legs and Cross

Start off by locating where the cross will need to be. This will be about midway up the stool so it will be connected with the legs 15 inches from the ground.

Drill holes before any type of screwing.

To ensure the holes match up, woodglue them together first before drilling. The wood glue doesn’t have to be completely dry but as long as it can hold the pieces together so that it is easier to drill. This way, the drill can go through the legs and cross to ensure the holes are aligned.

Use a power drill to apply a screw into the legs and cross and repeat this process for the other legs. Your stool should be able to stand after this.

Step 4: Creating and Connecting Leg Connectors

Creating and Connecting Leg ConnectorsCreating and Connecting Leg Connectors

Cut 4, 1x1s to 8.5 inches.

Cut the two sides at a 45-degree angle so that they are pointing towards each other.

Repeat this for all pieces

Attach these connectors at the center of the way up so they are parallel horizontally with the cross.

Mark up where you will place them and cut off the excess to make the width of the connector the same as the length of the leg.

Glue them together and drill a hole from the connector into the leg.

Screw the connectors and legs together.

Step 5: Adding the Bottom Leg

Adding the Bottom LegAdding the Bottom Leg

Cut out a 14.5 inch 1×1

Flip the stool over and glue the 1×1 to the center of the cross

Use 2 L-brackets on opposite sides to attach the 5th leg.

To attach the L-brackets, line them up with the leg and the bottom of the cross and draw in the holes.

Drill and screw to connect the L-brackets

Step 6: Sanding and Leveling Your Stool

Sanding and Leveling Your StoolSanding and Leveling Your Stool

Sand the base of the legs to make sure your legs are as even and flat as possible.

Sand the faces of the stool to smoothen out the surfaces and to get rid of any potential splinters.

Doing this manually is a hassle so a power sander is recommended.

Step 7: Attaching the Seat

Cut out a 17-inch diameter circle from a medium density fibreboard that is 0.75 inches thick.

Mark up the board to match the base of the legs. The outside edges of the boxes should be 5.75 inches from the center of the board.

Glue the legs to the board to stabilize the drilling process.

Drill and apply screws to connect the seat.

Step 8: Making It Sturdy

Making It Sturdy Making It Sturdy

Attach L-brackets from the cross to the inside of the legs. Mark the holes, drill, and screw.

Apply a second screw from the leg to the cross.

These two steps will secure the twisting of the legs and make it sturdier.

Step 9: Design

DesignDesign

Cut out a 22 inch radius circle from your red with white dots fabric.
Cut out 4, 16×16-inch rectangles from your tan fabric.
Using the velcro stickers attach the pillow to the seat.
Also using the velcro, attack the red fabric to the pillow and tan fabric to the leg connectors.

Be the First to Share

Recommendations

For original article click here

Add Comment

DIY Arts, Crafts & Sewing

Books

DIY Tools

DIY Kits

DIY Modern Wall Hangings | Easy DIY Wall Decor Projects for 2018
Art and Wall Decor | Kirklands
No Preview
DIY Room Decor!8 Easy and Useful DIY Decorating Ideas (DIY Wall Decor, Pillows, etc.)#11
How To Make A Simple Barn Wood Picture Frame Display | DIY | Homemade | Upcycle
Thrifted Furniture Makeover DIY | Their Trash Someone Else’s Treasure! | Ashleigh Lauren
DIY Closet System Tutorial
Make an Easy Deck Chair
18 deck chairs that will bring the seaside to your garden
Dyeing Clothing with RIT Fabric Dye – Vinegar and Salt Options
DIY fashion dress – yiv.Com
DIY: Sew a Dress from a Sheet | thetwinsofhearts
Steampunk Costumes, Clothing and Fashion
Make Grape Jelly at Home!
Christmas Chutney Recipe for Hamper Gifts // Tastefully Vikkie
HOW TO MAKE WILD GRAPE JELLY LIKE THE OLD-TIMERS DID
Make Delicious Cherry Jam With Ease Using Your Freezer
Thrifted Furniture Makeover DIY | Their Trash Someone Else’s Treasure! | Ashleigh Lauren
Dyeing Clothing with RIT Fabric Dye – Vinegar and Salt Options
DIY Modern Wall Hangings | Easy DIY Wall Decor Projects for 2018
Christmas Chutney Recipe for Hamper Gifts // Tastefully Vikkie